Subfloor Stress Saving Tools.

In my previous post I talked about my summer adventure ripping out and replacing the subflooring in my house.  In this post I will list and briefly discuss ten tools that I feel are absolute necessities to accomplish any subflooring repair or replacement job on the planet.    Though some tools on the list are probably more useful than others on the list, they are not listed in any particular order of importance.  This list is primarily discussing the tools that were most important in the removal of old subflooring, however I did use/need each one of these tools in the installation of the new subflooring as well.  Each tool listed in this post can be bought or researched by following the link provided below each picture.

#1 – The oscillating multi-tool

DSCF5833

Purchase Here

I did not own this tool when I started the job, but I do not think that I could have done/finished the job without it.  Oscillating multi-tools have many different functions and are compatible with many different attachments from sanding to cutting wood and metals.  These tools allow you to cut subflooring flush with walls and thresholds.  Demolition blades that cut both wood and metal allow you to move nail infested boards with relative ease.  This is the exact tool that I used for my project and although it was one of the cheapest oscillating multi-tools that I could find, it was worth its weight in gold.

 

#2 – Reciprocating Saw

DSCF5835

Purchase Here

Reciprocating saws perform similarly to oscillating multi-tools with the exception of having considerably more power and not being able to cut flush with walls or thresholds due to the blade not being offset like that of the multi-tool.  Like the multi-tool, demolition blades made for cutting through wood and metal can be purchased for this tool which make cutting through nailed and screwed lumber a much easier task.  When cutting along walls and thresholds I would typically cut as close as I could to the threshold with the more powerful, quicker cutting reciprocating saw and then come back with the multi-tool for a flush, more precise result.

 

#3 – Circular Saw

DSCF5839

Purchase Here

A circular saw is the way to go to remove subflooring when working in an open area away from walls, thresholds, and other tight areas.  They cut faster than a reciprocating saw and more accurately than a multi-tool.  Typically circular saws have guide plates that adjust for different depths of cut.  This is a very handy feature when you know the thickness of your subflooring.  For example, if you know that your subfloor is 3/4″ thick, you can set the depth of cut on your circular saw to 3/4″ and cut our a lot of material quickly without having to waste time being cautious not to cut through any of your floor joists.

 

#4 – Pry Bars

DSCF5836

Purchase Here

When both removing and replacing subflooring it is often required to remove any baseboards and floor trim in the area in order to cut the old subflooring flush with the wall.  You will likely need more than one pry bar in order to do this without ruining your trim and baseboards.  Pry bars are also needed to pry up old subflooring, move new subflooring into place, and removing protruding nails that will not allow new subflooring to lay flush.

 

#5 – Tape MeasureDSCF5843

Purchase Here

I like to think that this one is pretty obvious, so I will not insult anyone’s intelligence with an explanation.

 

#6 – Hammers/Maul

DSCF5837

Purchase Here

In some areas of my house the subfloor was so rotted that I just knocked it off with a hammer.  Hammers also come into play in positioning new subflooring into place, removing nails, and believe it or not hammering nails in.

 

#7 – Chisel

DSCF5845

Purchase Here

This chisel came in very handy when working in tight corners and places where the subfloor terminated under a wall where I could not get to it with the reciprocating saw or the multi-tool.  When that was the case I would just cut flush with the wall then use a hammer and chisel to remove the remainder of the board that lay between the wall and the floor joists.

 

#8 – Impact Driver

DSCF5842

Purchase Here

Impact drivers are great because they eliminate the need for predrilling a pilot hole before you screw into wood in most situations, which speeds up the building process greatly.  For subfloor removal purposes any type of drill (not specifically an impact drill/driver) will likely be needed in order to remove wood that is screwed to the floor joists.  Prying screws up with a pry bar can damage and split the joists, compromising their integrity.  I would specifically recommend an impact drill/driver for the installation of subflooring due to the fact that it will save you tons of time on drilling pilot holes and will not split your wood without them.

 

#9 – Headlight

DSCF5846

Purchase Here

This may seem a little off of the wall, but my house is not the best lit place in the world and although I did use a work light, I was often working in several rooms at a time and climbing up and down from below the house to back inside the house and the light refused to follow.  It is not practical to carry a flashlight around and I often found myself praying to grow a second, third, fourth, ad fifth arm out of necessity for holding boards and other tools anyway.  A headlight was invaluable to me on this project due to the amount of hands-free portable light that it provided.

 

#10 – Wet/Dry Vac

DSCF5841

Purchase Here

Installing a subfloor on a new construction home would likely eliminate the need for this tool to be on the list of necessities.  I was not installing a subfloor on a new construction home.  I was sawing, cutting, throwing, flinging, hammering, nailing, and screwing all in my one and only home, the place where I live, the place where my wife lives, and the place where my three kids live.  Needless to say if I worked in a dirt and dust production factory I would have been employee of the month.  This wet/dry vac made life a lot easier than it would have been without it.  I still used the old faithful broom and dust pan quite a bit, but the vac not only eliminated the need for them often, it did the job much quicker and more efficiently.

 

I would not attempt to tackle any subfloor replacement job without any one of these tools listed above.  The job could be done without them, but the time and effort that they will save you make it highly impractical.  Should you find yourself facing the task of replacing subflooring I hope that you do not find the need for these tools the hard way as I did.  If you found this post useful or simply liked the read I would appreciate it if you would like, comment, and subscribe below.  Should you have any questions or concerns please do not hesitate to contact me.  Thank you!

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: